CybertruckCo Lift Rod Kit - Front Install Only Result

D-Stew said:

So I bought the Lift Rod kit, at only $80 for the full set of 4 it was an easy decision. Why? I don’t like how the front nose sits lower than the rear end of the truck. It may be for aerodynamics, but I don’t care. I wanted it higher in the front. With that I didn’t install the rear pair, and did the front only. The results speak for themselves. In entry/low mode as shown in the photo it now sits basically level. Install was super easy, took seriously 2 minutes per side.

According to @CYBERTRUCKco at stock height, the front sits in low mode at 37.125” and the rear at 37.825”. With this kit installed in the front only, the front end now sits 1” taller at 38.125” making it just slightly higher than the stock rear height. Exactly what I was looking for. I did this for aesthetics only and this was a quick and easy solution. Highly recommend if you want the same look.

Here’s link to buy: https://cybertruckco.com/product/cybertruckco-lift-rod-kit-raises-truck-625-2-height-over-stock/

Click to expand...

D-Stew said:

So I bought the Lift Rod kit, at only $80 for the full set of 4 it was an easy decision. Why? I don’t like how the front nose sits lower than the rear end of the truck. It may be for aerodynamics, but I don’t care. I wanted it higher in the front. With that I didn’t install the rear pair, and did the front only. The results speak for themselves. In entry/low mode as shown in the photo it now sits basically level. Install was super easy, took seriously 2 minutes per side.

According to @CYBERTRUCKco at stock height, the front sits in low mode at 37.125” and the rear at 37.825”. With this kit installed in the front only, the front end now sits 1” taller at 38.125” making it just slightly higher than the stock rear height. Exactly what I was looking for. I did this for aesthetics only and this was a quick and easy solution. Highly recommend if you want the same look.

Here’s link to buy: https://cybertruckco.com/product/cybertruckco-lift-rod-kit-raises-truck-625-2-height-over-stock/

Click to expand...

Wolfgram said:

Thanks for sharing! I plan to raise mine with these parts… but I’ll do front and back. Did you notice any difference in comfort/bump harshness or handling?

Click to expand...

Gaximus said:

It’s a bad look. Level looks good, front a little lower is slightly worse, but front higher is the worse possible look. It’ll also ruin your headlight aiming. You’ll be blinding everyone with just your low beams.

Click to expand...

Cyberus said:

When I saw this, I knew it was someone in Southern California. ?

Anyone who doesn’t live here, wouldn’t understand.

I do think we’re going to get an update that will allow adjustments to the ride height independently front and rear. The nose does tend to dive at times when it should raise.

Click to expand...

Wolfgram said:

I lived in SoCal for a number of years… but I don’t get it. Why is a level truck important?

Click to expand...

Gaximus said:

I level truck is symmetry. And 4x4 trucks usually come level, 2x4 typically sit higher in the rear factory. But this mod isn’t level. It’s nose up. Which gives it that “broken rear suspension “ look, that some prefer.

Click to expand...

Pops said:

Anyone can adjust the position of the headlights in the service menu, its a pretty nice feature.

Honestly it looks fine to me, but I do not even notice the difference. Maybe if I saw it side by side with stock CT I would notice it.

Click to expand...

RVAC said:

Looks like they need to make a set of lift rods that aren't quite as tall just for the front as this kit raises it too high.

Click to expand...

Freemarket said:

The photo I posted that you commented on, only had the lift bars in the front, that’s why the front appeared higher than the rear, it was.

Click to expand...