Search results

If you raise it to “high” it remembers location. Hard to tell from the picture, but I think I’d take out all of the cinderblock and put a thinner railing flush with the staircase wall. That’d give you more than the 3-4” you need. Seems like leaving the bottom block row might be a tripping hazard.

I tested it out pretty thoroughly on the X I had while my car was in the shop and it did not do this. The cut off was seamless. Sometimes it does it in the truck, sometimes not and I haven’t been able to figure out what variable might make the difference.

Yes!! Sometimes it runs in what I feel like is a shorter cycle and shuts off seamlessly with no movement. It also doesn’t do it in service mode for me. I figured it was likely some byproduct of system design and normal operation, but wanted to be sure so I mentioned it when I had to bring my...

Thanks. None of that is quite what I’m referring to though. This occurs at the end of a compressor cycle. Self-leveling and self-adjusting is smooth and calculated. This is a significant bump you wouldn’t associate with normal operation. The poster before you described it like a car bumping in...

Thanks. I hadn’t made that connection. I was thinking it would be like my 3 where it would stay off when selected.

I have noticed quite often that my car’s rear end tends to momentarily bounce up as the compressor finishes a cycle, possibly a longer than normal cycle. It’s like a burst of air made it in as the system shut off. You can also faintly hear what sounds like a flap or valve closing. It’s only...

On a separate issue, my wiper always defaults to “auto”. It has randomly turned on multiple times when facing the sun. The dry blade makes the windshield hazy and much harder to see out of. I hit the wiper icon and manually select off, but it never stays “off”. The next time I drive or the car...

I had several large scratches worse than yours. It looked like someone slide down my hood with nails in their pockets. I took it in and the ground/polished it out and it looks perfect now. I don’t think you need a new panel for that.

I’m in San Diego. I was contacted a few days after delivery, but it took 2.5 months to “receive the equipment from Tesla”. It was finally installed Monday.

Search digital camo on metro There are tons of digital camp prints on this site. Search around. This one looks close https://metrorestyling.com/products/metro-wrap-large-digital-midnight-camouflage-vinyl-film

Great idea! I’ll give the roller a shot. I bought some of that 303 last year for some patio furniture. I didn’t realize it was used on cars too. Thanks

Forget the stainless steel, what is everyone using to clean that giant lint collector of a dashboard?? My first go with a swiffer duster made it worse. I’d also take any pro tips on keeping the exterior plastic trim protected and looking nice.

Yes. Mine is the exact same. After reading your post, I noticed it a bit during early regen too. I was paying more attention to it today and it was most apparent in the early 30s just like in your video.

Mine does this too. I feel that it is associated with a low power setting and not a speed, though it is probably more noticeable in the range you mention when I’m not accelerating and there isn’t much noise. I don’t get it during any amount of green on the regen indication . It’s only audible...

Pest control San Diego to Tucson ?

Got my truck delivered today. Gdamn this thing is amazing!!

They had me in Irvine and never switched it when they started deliveries in Carlsbad for whatever reason

I saw my VIN in the app yesterday. No email so it’s possible it came late 2/22. Rn11278 ordered AWD 12/12 vin24XX Registered for Carlsbad, CA delivery location down in socal. Bing bang boom! Can’t wait!!

Adding a gateway or battery should not change your NEM status (IE from nem2 to nem3) according to the CPUC ruling. pg.166 https://docs.cpuc.ca.gov/PublishedDocs/Published/G000/M500/K043/500043682.PDF