🚀 Share Your Best Cybertruck Hacks: Tips, Tricks, and Upgrades 🔧✨ Win a Prize

[Stickercity]

Calling all Cybertruck DIY enthusiasts! ?? This thread is all about sharing effective DIY hacks to upgrade or enhance your Cybertruck. Whether it's a clever storage solution, a protection mod, or a quick aesthetic upgrade, we want to hear from you!

? Challenge: Post your favorite DIY hack, complete with photos, instructions, or tips. The most creative or useful idea will get a special shoutout (or maybe even a little prize ?)!

Here are a few to kick things off:

• Adding fender flare protection to prevent scratches.
• Installing 5D carbon fiber wraps on wheel spokes for a sleek look.
• External sunroof tinting to reduce UV heat and add style.

Let’s inspire each other to make our Cybertrucks the best they can be! ?

Sponsored

 

[smcnaughton829]

I don’t have a hack but I would love a light on the underside of the center arm rest. Every time I open it at night I can’t see anything due to the tray blocking the light inside.

 

[Stickercity]

I don’t have a hack but I would love a light on the underside of the center arm rest. Every time I open it at night I can’t see anything due to the tray blocking the light inside.

Not seeing would be considered a problem. Thank you for sharing and we will review this idea

 

[3cyberbeast]

Calling all Cybertruck DIY enthusiasts! ?? This thread is all about sharing effective DIY hacks to upgrade or enhance your Cybertruck. Whether it's a clever storage solution, a protection mod, or a quick aesthetic upgrade, we want to hear from you!

? Challenge: Post your favorite DIY hack, complete with photos, instructions, or tips. The most creative or useful idea will get a special shoutout (or maybe even a little prize ?)!

Here are a few to kick things off:

• Adding fender flare protection to prevent scratches.
• Installing 5D carbon fiber wraps on wheel spokes for a sleek look.
• External sunroof tinting to reduce UV heat and add style.

Let’s inspire each other to make our Cybertrucks the best they can be! ?

To keep my Cybertruck clean, I use all attic acid. I dissolve that with some alcohol and then add water. I do a very quick spray around the truck with Stainless steel pump sprayer and spray all the stainless steel which takes less than a minute and then drive it through a high-quality automatic Carwash. And the stainless steel comes out, amazingly clean, and I do have the ceramic spray added to the wash, and that adds a small level of protection against fingerprints. I would say it last about a week where the fingerprint will not show up and then they do start showing up if people do touch the exterior.

 

[theoldguy]

I probably shared this before, but any chance to show off lol...
I made a frunk MOLLE
Ive recently seen a company now selling a product that doesn't require drilling or screws. The process is always being improved

 

[Stickercity]

I probably shared this before, but any chance to show off lol...
I made a frunk MOLLE
Ive recently seen a company now selling a product that doesn't require drilling or screws. The process is always being improved

I love the creativity of this! Really love to see how talented people get when they want something! Thank you for sharing I hadn't seen this before

 

[Stickercity]

To keep my Cybertruck clean, I use all attic acid. I dissolve that with some alcohol and then add water. I do a very quick spray around the truck with Stainless steel pump sprayer and spray all the stainless steel which takes less than a minute and then drive it through a high-quality automatic Carwash. And the stainless steel comes out, amazingly clean, and I do have the ceramic spray added to the wash, and that adds a small level of protection against fingerprints. I would say it last about a week where the fingerprint will not show up and then they do start showing up if people do touch the exterior.

Have you done a video displaying this?

 

[3cyberbeast]

Have you done a video displaying this?

No, that’s what I used to do When I was testing different Methods. After I find out that wrapping your vehicle, you cannot run your vehicle through the car wash I was like oh hell no that is not going to work for me. So now seeing as I own a car wash I just have the car wash automatically injected in the first pass When I wash my CT. I buy the powdered crystals and the crystals don’t Dissolve easily in water so I add alcohol then you gotta separate the large particles and put that in a 1 gallon or a half gallon spray. I tried it out in a self-serve stall, and it worked just as good as the High quality Roll over automatic car wash, Whether I sprayed it just before or as the first pass of the automatic The results are the same, It just needs to sit on there for about a minut. I also would not recommend Touch free car wash But if there is not a high-quality rollover automatic, I would say touch tree is fine. You can buy the crystals on Amazon as well as the half gallon or gallon stainless steel sprayer.

 

[The Tesla Guy]

To keep my Cybertruck clean, I use all attic acid. I dissolve that with some alcohol and then add water. I do a very quick spray around the truck with Stainless steel pump sprayer and spray all the stainless steel which takes less than a minute and then drive it through a high-quality automatic Carwash. And the stainless steel comes out, amazingly clean, and I do have the ceramic spray added to the wash, and that adds a small level of protection against fingerprints. I would say it last about a week where the fingerprint will not show up and then they do start showing up if people do touch the exterior.

Assuming that’s a typo. And that you’re not using something called all attic acid. (not a real thing as far as I know)
Are you talking about muriatic acid?
That’s not really a recommended chemical. So more likely citric acid?

 

[Cyber_Punk_SFL]

I probably shared this before, but any chance to show off lol...
I made a frunk MOLLE
Ive recently seen a company now selling a product that doesn't require drilling or screws. The process is always being improved

https://www.cybergearco.com/products/cybertruck-frunk-molle-panels

i bought them, they arrive next week

 

[jimnycricket65]

I like my truck looking rugged and dirty. ?

 

[Stickercity]

I like my truck looking rugged and dirty. ?

Sounds like your truck's living its best life in 'grunge mode.' Who needs a car wash when Mother Nature’s out here doing custom dirt wraps for free? ?

 

[Stickercity]

https://www.cybergearco.com/products/cybertruck-frunk-molle-panels

i bought them, they arrive next week

would love to hear some feedback

 

[Jesseg9163]

Not seeing would be considered a problem. Thank you for sharing and we will review this idea

I’m pretty sure there is a light down there that lights up the center floor section.

 

[BeFamousVideo]

I don’t have a hack but I would love a light on the underside of the center arm rest. Every time I open it at night I can’t see anything due to the tray blocking the light inside.

You're on to something here. An under seat light that projects to the back seat floor would be helpful. Now that I wrote this I'll try USB 8"X1" bar lights they magnetically attach to steel and can be motion operated.

Sponsored