Daily random Cybertruck photos thread - Post Yours! 📸 🤳

[Roger@CYBERTRUCKco]

Just doing some chores

Your missing the end

Can't wait for a lift kit on the new non-air suspension Cybertrucks. I think that's when we'll see 37's routinely...

Our kit will work on all Cybertrucks

Sponsored

 

[Kryptek]

Rip 🪦 vin 47921 ‍🩹

 

[raww1023]

Rip 🪦 vin 47921 ‍🩹

What’s happened?

 

[FHWizard]

Your missing the end

Our kit will work on all Cybertrucks

I like the flexibility of enclosing the frame for a larger camper shell (I have the full kit) or leaving it open like this to use as a lumber rack.
(And thanks for sending me the other set of rails. Got them today.)

 

[RayzorBEV]

My outside thermometer is registering 115 degrees
Time to deploy Tesla Shields. Stay frosty, y'all

 

[Roger@CYBERTRUCKco]

Just doing some chores

What happened to the second row or top edges?

It looks all jacked-up and I'm not sure that's a good look. I imagine it can't go any higher than the stock air suspension goes in "Extract" mode?

let’s start with a public apology for giving you the finger last summer, that was not needed. Will you forgive me my trespass?

we added the wind dam to improve range, looks cool in person, but everybody likes different things.

pics below, offroad mode, very high offroad mode and extract with 20” belly clearance. All modes are 4” taller as we lowered the subframes and suspension, updated upper control arms.

 

[Kryptek]

What’s happened?

Driver hit me

 

[HaulingAss]

let’s start with a public apology for giving you the finger last summer, that was not needed. Will you forgive me my trespass?

I guess you just blended in with all the crazies/haters, I never knew one of them was actually you!

In any case, no hate, I'm just saying I think it looks kinda "off" being all jacked up like that. No big deal, just one man's opinion, not to be taken personally.

 

[hemiarch]

I guess you just blended in with all the crazies/haters, I never knew one of them was actually you!

In any case, no hate, I'm just saying I think it looks kinda "off" being all jacked up like that. No big deal, just one man's opinion, not to be taken personally.

 

[Kryptek]

I guess you just blended in with all the crazies/haters, I never knew one of them was actually you!

In any case, no hate, I'm just saying I think it looks kinda "off" being all jacked up like that. No big deal, just one man's opinion, not to be taken personally.

I think a wide body kit and maybe a 1-2” spacers would look kick ass on that! it does look a lil wonky no offense ment

 

[petercyber]

What happened to the second row or top edges?

let’s start with a public apology for giving you the finger last summer, that was not needed. Will you forgive me my trespass?

we added the wind dam to improve range, looks cool in person, but everybody likes different things.

pics below, offroad mode, very high offroad mode and extract with 20” belly clearance. All modes are 4” taller as we lowered the subframes and suspension, updated upper control arms.

I absolutely love it, however, not with these pizza cutters, 37"s are next.
Also, can you develop " as we lowered the subframes and suspension " ? english please?

 

[Roger@CYBERTRUCKco]

I think a wide body kit and maybe a 1-2” spacers would look kick ass on that! it does look a lil wonky no offense ment

Wide body fender tooling is being cut this next week!

sneak peak at the rear fender, 2.5” wider

 

[Kryptek]

Wide body fender tooling is being cut this next week!

sneak peak at the rear fender, 2.5” wider

I was contemplating 3d printing a set in carbon fiber filament it would be very expensive but diy is awesome if you can make it look legit!

 

[Kryptek]

Closest thing I have to a cyber now

 

[Roger@CYBERTRUCKco]

I absolutely love it, however, not with these pizza cutters, 37"s are next.
Also, can you develop " as we lowered the subframes and suspension " ? english please?

We did a body lift, subframe drop, so all motor, steering and suspension still works as designed and does not stress axels or other components. This allows full suspension articulation without risk damaging drive or suspension.

Cost will be $8000, can be configured 3, 4 and 5” lift and is not DIY, requires a lift.

it’s likely we’ll make a “mall crawler” 2” version that is simply a suspension spacer with new upper control arms that will be about half the cost and DIY.

I was contemplating 3d printing a set in carbon fiber filament it would be very expensive but diy is awesome if you can make it look legit!

wont be diy, we also have a plastics manufacturing company.

Sponsored