Any suggestion of tailgate spare tire mount solution??

[jackychu]

Looks like UP is only one who has rear bumper with tire mount product.
But it always backorder. Don't know when will receiver it.
Does any other product in the market?

Sponsored

 

[hemiarch]

I would love to know the answer to this as well

 

[TebisYang]

The plastic parts of the tailgate (above the light bar) can be replaced with stainless steel, where M6 rivet nuts can be installed. Paired with the lower edge line of the rear door, a MOLLE panel can be implemented—just ensure the 7-hole wheel hub avoids the camera.

 

[TebisYang]

A few days ago when I had some free time, I made a rough prototype to test the concept. If you guys like it, I’ll try to find time soon to finish a proper version for reference.

 

[misdemeanor]

A few days ago when I had some free time, I made a rough prototype to test the concept. If you guys like it, I’ll try to find time soon to finish a proper version for reference.

Would like to see that prototype

 

[CT_AZ_4x4]

A few days ago when I had some free time, I made a rough prototype to test the concept.

Following to see the outcome/result! Thank you.

 

[UP_Kirk]

Looks like UP is only one who has rear bumper with tire mount product.
But it always backorder. Don't know when will receiver it.
Does any other product in the market?

@jackychu,

Our backorder queue is shrinking as we continue to ramp up production.
If you need assistance with any @Unpluggedperformance Cybertruck products, please let me know. The rear bumpers have been shipping nationwide since Q4 '24

@UP_Kirk

 

[jackychu]

Would like to see that prototype

Yes. Very interesting. Please share. Thanks.

 

[CYBERTRUCKco]

Looks like UP is only one who has rear bumper with tire mount product.
But it always backorder. Don't know when will receiver it.
Does any other product in the market?

Yes, we have a new heavy-duty offroad rear bumper going to launch this week for delivery end of May!

• Best on market rear departure angle!
  • 27" on the corner vs 213" on the OEM (similar to competitors bumpers we have seen)
  • 21" at the lowest point vs 16" rear bumper diaper.
• 1/4" thick aluminum rear bumper weights in a 65lbs
• mounts to factory frame locations with no modifications
• You can remove the factory tow hitch if you won't be towing and want better clearance, or It uses the factory tow hitch, to avoid voiding warrantee and it is certified by Tesla for towing.
• Optional stainless steel rear tire swing away on the passenger side and swing away molle shell on the driver side. Both have rear quarter panel "stegosaurus" vertical protection plates.
• Have I mentioned we've been build offroad bumper, sliders, and other parts since 2005
• The swing away rear tire carrier has 3x locking positions (Closed, 90° to clear rear bed or open to use the folding table option) so it's not wild when released. Also 2x locks when closed to make sure it never comes open without your direct input.

We haven't put on the site yet because we don't want to tell you next month and then take 12+ months to deliver.

Let me know your thoughts!

 

[Urander]

Here's a post that I hope helps!
https://www.cybertruckownersclub.co...uring-mounted-to-underside-of-bed-rack.36442/

Fwiw, one CT owner tested our flat panel rack and recorded only 419 Wh/mi at 70 mph - just 3% more than without a rack. https://www.cybertruckownersclub.co...range-loss-was-way-lower-than-expected.40606/

 

[jackychu]

Yes, we have a new heavy-duty offroad rear bumper going to launch this week for delivery end of May!

• Best on market rear departure angle!
  • 27" on the corner vs 213" on the OEM (similar to competitors bumpers we have seen)
  • 21" at the lowest point vs 16" rear bumper diaper.
• 1/4" thick aluminum rear bumper weights in a 65lbs
• mounts to factory frame locations with no modifications
• You can remove the factory tow hitch if you won't be towing and want better clearance, or It uses the factory tow hitch, to avoid voiding warrantee and it is certified by Tesla for towing.
• Optional stainless steel rear tire swing away on the passenger side and swing away molle shell on the driver side. Both have rear quarter panel "stegosaurus" vertical protection plates.
• Have I mentioned we've been build offroad bumper, sliders, and other parts since 2005
• The swing away rear tire carrier has 3x locking positions (Closed, 90° to clear rear bed or open to use the folding table option) so it's not wild when released. Also 2x locks when closed to make sure it never comes open without your direct input.

We haven't put on the site yet because we don't want to tell you next month and then take 12+ months to deliver.

Let me know your thoughts!

Looks very low profile. Very nice. When can place the order? And you said will ship at end of May?
Do you offer installation?
I have your running board installed by myself. But it is easy one.
Bumper should be very heavy. I am not sure I can install it by myself.
I also pre-order console refrigerator. Can't wait for delivery

 

[TebisYang]

Would like to see that prototype

The replacement of the plastic part above the original light strip has been put on hold because the body-color matching material is difficult to procure. It may be completed in May.

 

[Speedr]

Yes, we have a new heavy-duty offroad rear bumper going to launch this week for delivery end of May!

• Best on market rear departure angle!
  • 27" on the corner vs 213" on the OEM (similar to competitors bumpers we have seen)
  • 21" at the lowest point vs 16" rear bumper diaper.
• 1/4" thick aluminum rear bumper weights in a 65lbs
• mounts to factory frame locations with no modifications
• You can remove the factory tow hitch if you won't be towing and want better clearance, or It uses the factory tow hitch, to avoid voiding warrantee and it is certified by Tesla for towing.
• Optional stainless steel rear tire swing away on the passenger side and swing away molle shell on the driver side. Both have rear quarter panel "stegosaurus" vertical protection plates.
• Have I mentioned we've been build offroad bumper, sliders, and other parts since 2005
• The swing away rear tire carrier has 3x locking positions (Closed, 90° to clear rear bed or open to use the folding table option) so it's not wild when released. Also 2x locks when closed to make sure it never comes open without your direct input.

We haven't put on the site yet because we don't want to tell you next month and then take 12+ months to deliver.

Let me know your thoughts!

That looks great!!!

PLEASE don't cost a fortune...

 

[hemiarch]

Yes. It really does look great

 

[bigmoose70]

@jackychu,

Our backorder queue is shrinking as we continue to ramp up production.
If you need assistance with any @Unpluggedperformance Cybertruck products, please let me know. The rear bumpers have been shipping nationwide since Q4 '24

@UP_Kirk

With the tire mount it blocks the rear view camera right?

Sponsored