3D Printer Files for Cybertruck items?

[AverageJoe]

Bought file off cults3d

Sponsored

 

[Mark V]

Has anyone tried this? Does it work?
https://www.printables.com/model/998602-cybertruck-tonneau-seal

 

[TeslaKen]

Has anyone tried this? Does it work?
https://www.printables.com/model/998602-cybertruck-tonneau-seal

I don't think it leaks there but I guess you could print and try it and see if you get any change, but typically if it leaks it leaks where the glass roof meets the seal in the rear.

 

[Mark V]

I don't think it leaks there but I guess you could print and try it and see if you get any change, but typically if it leaks it leaks where the glass roof meets the seal in the rear.

Thanks. I was just curious as well have seen so many other suggestions, but never saw that before I was looking around the Printables website.

 

[DarkEye]

Has anyone seen any 3d printer files for the left and right side mirrors? I'm talking about a cap you fit over the side mirrors like these.

 

[drewm]

I created a Cybertruck Food Tray for use while driving since there's no real place to put food down without it falling on the floor or making a mess inside your wireless charger

https://makerworld.com/en/models/1783579-cybertruck-food-tray

I could also make a short one that only covers the wireless charger area if people are interested

 

[Sandman1962]

I like it! From personal experience I would worry about the longevity of those tabs (given how small the horizontal surface area seems to be) I’ll probably add some reinforcement.
The idea is great since the OEM charging area really wasn’t executed well for iPhone users like me.
I often daydream about printing dual MagSafe chargers in that area. I really use a qi charger attached to the main screen but still want to make that area functional as intended.

 

[drewm]

I like it! From personal experience I would worry about the longevity of those tabs (given how small the horizontal surface area seems to be) I’ll probably add some reinforcement.
The idea is great since the OEM charging area really wasn’t executed well for iPhone users like me.
I often daydream about printing dual MagSafe chargers in that area. I really use a qi charger attached to the main screen but still want to make that area functional as intended.

I agree, I was also concerned mostly as the tabs are printed in the weaker direction and they do bend and latch. They are 2mm thick, although PETG is pretty flexible. I might redesign those tabs to be thicker and not have to bend as much to latch or find a way to print them separately in the other orientation, but I'll see how mine does in my car for now.

 

[devdrone6]

Does anyone know/have a 3d printed clip to use air freshener pods in the cybertruck - like the febreeze ones?

 

[eser50]

Has anyone figured a way to retrofit a magsafe charger into the current wireless charger location? I know we can't remove the actual charger itself because of the key sensor, but overlaying it would be fine too.

 

[devdrone6]

This is what i have:

https://www.cybertruckownersclub.co...n-before-challenge-thread.47813/post-30663734

Has anyone figured a way to retrofit a magsafe charger into the current wireless charger location? I know we can't remove the actual charger itself because of the key sensor, but overlaying it would be fine too.

 

[Gaximus]

Im actually looking to make a better MageSafe/QI charger. I’m looking for a 3d model that clips into the trim, I've seen a few on amazon, but just need to find a 3d model i can modify. There are no good MagSafe mounts for any vehicles.

 

[eser50]

Im actually looking to make a better MageSafe/QI charger. I’m looking for a 3d model that clips into the trim, I've seen a few on amazon, but just need to find a 3d model i can modify. There are no good MagSafe mounts for any vehicles.

That's exactly what I'm looking for as well. I also want it to be flat so I can wrap it in the gray alcantara to match. I guess I have to try my hand at some 3D design...

 

[drewm]

A post about the rear seat Phone/Tablet holder that fits a front seat with a fixed headrest that I just designed and published https://www.cybertruckownersclub.co...hone-tablet-holder-for-rear-passengers.48399/

 

[Sandman1962]

I uploaded the files to Makerworld

https://makerworld.com/en/models/1859081-cybertruck-magsafe-charging-pad#profileId-1988148

If you are interested, try it out.

The chargers I used :

https://www.amazon.com/dp/B0DLP157QH?ref=ppx_yo2ov_dt_b_fed_asin_title&th=1

The cord:
https://www.amazon.com/dp/B0DSJ2SLSY?ref=ppx_yo2ov_dt_b_fed_asin_title&th=1

If you don't have a 3D printer set up or a friend with one, I'll print one out in PETG-Carbon fiber for $20 plus USPS shipping - probably around $9 in their padded envelopes. If you wanted me to send you out a completed setup, it's $75 plus shipping.

If you print one out and like it, let me know and if you wanted to buy me or anyone else a cup of coffee, that is payment enough.

Good luck to us all.

Sponsored