Where are the aftermarket bumpers?

[CYBERTRUCKco]

Tell me about this Lucerne event! If it's this weekend, I'll be there with my truck ??

www.smugglersruns.com
Use coupon CYBERTRUCKco for $100 off or email and ask for special deal ;ask minute...

Sponsored

 

[Roger@CYBERTRUCKco]

A few photos from last weekend and some testing

 

[Roger@CYBERTRUCKco]

Finally had enough time to get back to this… the shape looks solid, adds tons of departure angle. Will start cutting aluminum next week to fabricate.

Let me know what you think?

 

[Pops]

That looks very promising! How will it integrate with the tow hitch?

 

[CYBERTRUCKco]

That looks very promising! How will it integrate with the tow hitch?

It utilizes the OEM tow hitch under the bumper so you can use the bumper either way for your needs. If you don't use the tow hitch, then 2x recovery hooks mount where the tow hitch would.

 

[L3it3R]

Very interested to see where that goes!

 

[btcrealm]

Finally had enough time to get back to this… the shape looks solid, adds tons of departure angle. Will start cutting aluminum next week to fabricate.

Let me know what you think?

Yes this is the kind of offroading change we need!

• Still need to make sure it has or keeps the hitch.
• Should have tow hooks on both sides (something like the stock front).
• Should cover anything vulnerable underneath it.

All these may be in your plans but they are what I see as important. You've already covered the tucking and departure angles.

 

[btcrealm]

First prototypes tested? minor changes and next week we’ll have ready for the website. Will be testing this weekend at the

1. Engineered and Made in the USA
2. Heavy gauge Aluminum - 48lbs each
3. Matte Black finish matches plastics
4. Plastic wear pads (steel option)

Let me know what you think?

The concept looks good. How good are they at being actual rock sliders? Any issue with rhino lining them or similar?

 

[Killlbox]

Add me to the list of people who want to replace the awful plastic.

I don’t want or need anything “tacticool”. I just want metal instead of plastic.

 

[sefar]

following... I like the sliders that get rid of the plastic in the back, especially since I have already torn one off!

 

[Roger@CYBERTRUCKco]

Yes this is the kind of offroading change we need!

• Still need to make sure it has or keeps the hitch.
• Should have tow hooks on both sides (something like the stock front).
• Should cover anything vulnerable underneath it.

All these may be in your plans but they are what I see as important. You've already covered the tucking and departure angles.

All points covered?

 

[CYBERTRUCKco]

The concept looks good. How good are they at being actual rock sliders? Any issue with rhino lining them or similar?

They are actual rock sliders, you can also jack off any spot on them!

No issue with Rhino lining them!

 

[btcrealm]

They are actual rock sliders, you can also jack off any spot on them!

No issue with Rhino lining them!

They are still in preproduction right? You are still working on both bumpers and the rock sliders, nothing on market yet.

 

[CYBERTRUCKco]

They are still in preproduction right? You are still working on both bumpers and the rock sliders, nothing on market yet.

First articles approved for production today, will photograph with all the plastic wear pads on them and add to site next few days, shipping in 3 weeks or less.

Install takes 2-3 hours, only trimming on the plastic inner fender with scissors to slide inside the bumper.

 

[MICyber]

I would love a front bumper with a wench mount but...

It seems like Unplugged Performance is the only vendor listing front or rear bumpers, and most or all of their products are in preorder/backorder mode. Not to mention their prices are roughly >2x than similar products for other trucks.

There have been CTs on the road for over 6 months. I wonder how long it will take for the aftermarket to mature.

Plus the two I've seen are a min $2500. Rough Country, Steelcraft or Realtruck have nothing.

Sponsored