XPEL Armour piece for rear seat underside

[jameslook]

Does anyone currently make a XPEL armour piece for the underside of the rear seats?
My Raptor dog did a number on it.
The OCD is kicking in and I was hoping to replace the piece or cover it up.
I wouldn’t be able to cut a piece properly so I was hoping someone made one.

Sponsored

 

[That Beast Mode]

Does anyone currently make a XPEL armour piece for the underside of the rear seats?
My Raptor dog did a number on it.
The OCD is kicking in and I was hoping to replace the piece or cover it up.
I wouldn’t be able to cut a piece properly so I was hoping someone made one.

Try giving a shout out to @AO-Pete he might be able to make one for you. I'd assume no one has this currently as I don't think it would be a high demand item except a specific use case like yours.

 

[jameslook]

Try giving a shout out to @AO-Pete he might be able to make one for you. I'd assume no one has this currently as I don't think it would be a high demand item except a specific use case like yours.

Awesomeness. Will do.
Yes, the combination of Raptor Dog and my OCD is unique.

 

[That Beast Mode]

Awesomeness. Will do.
Yes, the combination of Raptor Dog and my OCD is unique.

Fully understood - my OCD would not allow those scratches either. Hopefully Pete can hook you up, he's the go-to for all the armor stuff here.

 

[AO-Pete]

Well, without a picture of Raptor Dog, I don't think there's much we can do.

The small problem is, we no longer have our Cybertruck (It was subject to a buyback). I've got various bits of a Cybertruck, but the rear seat isn't one of them, so it's just getting the dimensions that would be the challenge. I know it's the underside of the seat assembly. Is it a fairly simple shape that you could measure? Even then, there's a lot of nuance to the measurement of the target surface versus the actual armor that goes on it, and a LOT of testing/iterating.

 

[MCraft99]

You could buy the Urander pet seat cover. It'll protect the doors from getting like that too.

 

[jameslook]

Well, without a picture of Raptor Dog, I don't think there's much we can do.

The small problem is, we no longer have our Cybertruck (It was subject to a buyback). I've got various bits of a Cybertruck, but the rear seat isn't one of them, so it's just getting the dimensions that would be the challenge. I know it's the underside of the seat assembly. Is it a fairly simple shape that you could measure? Even then, there's a lot of nuance to the measurement of the target surface versus the actual armor that goes on it, and a LOT of testing/iterating.

yes I could measure it but it isn’t exactly a completely flat and square piece.

 

[jameslook]

 

[jameslook]

You could buy the Urander pet seat cover. It'll protect the doors from getting like that too.

In his defence it happened the very first time he was in the Cybertruck and I decided I would put the rear seats up. He jumped in the back thinking there was a seat there and well…
So it was kind of my fault.

 

[kpanda17]

In his defence it happened the very first time he was in the Cybertruck and I decided I would put the rear seats up. He jumped in the back thinking there was a seat there and well…
So it was kind of my fault.

id buy a piece to protect
My rear seats are up all of the time
Subject to impacts and scratches

 

[AO-Pete]

Nah. I don't believe he'd do anything like that

The good news is those parts are not very expensive if it's parts one and two shown here that we're talking about?

 

[jameslook]

Nah. I don't believe he'd do anything like that

The good news is those parts are not very expensive if it's parts one and two shown here that we're talking about?

Yes that is correct.
How do you get those parts? Do you book a service appointment and mention the part numbers?
Unless there is some magic way to actually order the parts? I’m in Canada and I’m not a dealer so I don’t have access to select the parts for purchase from the catalog.

 

[AO-Pete]

I think everyone has access to the EPC these days, I don't think it's different for Canada, but I stand to be corrected. I do have the dealer view, but it should work for you as well, and yes, at least in the US, they'll offer the option for SC collection if they have stock there, otherwise, they'll ship them.

https://epc.tesla.com/

 

[jameslook]

I think everyone has access to the EPC these days, I don't think it's different for Canada, but I stand to be corrected. I do have the dealer view, but it should work for you as well, and yes, at least in the US, they'll offer the option for SC collection if they have stock there, otherwise, they'll ship them.

https://epc.tesla.com/

it works now! Awesomeness!
Hopefully I can figure out how to replace it once the part arrives.
Thanks everyone for the suggestions and help!

 

[AO-Pete]

it works now! Awesomeness!
Hopefully I can figure out how to replace it once the part arrives.
Thanks everyone for the suggestions and help!

I had a quick look, and feel like this is the right section, but wasn't able to find the bottom covers: https://service.tesla.com/docs/Cybe...UID-82AD8168-D351-4C84-BBA6-E4A8002E07AC.html

In any case, probably just a bunch of trim clips (which you'll need to keep from the panels you remove), and, worst case, a couple of 10mm bolts.

If you're up for it, I'll buy the old panels from you when you're ready, and get the Armor designed for them.

Sponsored