3D print mount for Uniden radar detector

[itsamti]

Sounds good.

I ordered and chose Global standard shipping as recommended by pcbway support. Total came out 44 dollars after 5 dollar coupon. Will update once I get it.

All done. Thanks!

Sponsored

 

[JUSTICEQD]

I tapped 2 wires into the 2-pin connector inside cabin camera housing. That connector provides around 15V which in operation range of Uniden R7/R8

I did the same, but because the camera is always powered, the R8 doesnt turns off when parked and away from the truck. You have that issue?

.

 

[gaubong053]

I did the same, but because the camera is always powered, the R8 doesnt turns off when parked and away from the truck. You have that issue?

.

There are two workarounds:
1. Enable power-saving mode for the R8. However, you’ll need to manually press the power button to power it back on for each use.
2. Set the dim mode of the R8 so that its screen only displays when necessary. Additionally, turn off Sentry mode at home. This is the method I’m currently using.

 

[itsamti]

I did the same, but because the camera is always powered, the R8 doesnt turns off when parked and away from the truck. You have that issue?

.

I ran usb c cable from radar detector to usb c port instead of tapping. Not too bad of work. I am think to get motion sensor to auto on and off https://a.co/d/bYWhDn0

 

[JUSTICEQD]

There are two workarounds:
1. Enable power-saving mode for the R8. However, you’ll need to manually press the power button to power it back on for each use.
2. Set the dim mode of the R8 so that its screen only displays when necessary. Additionally, turn off Sentry mode at home. This is the method I’m currently using.

RTFM Yeah, I should have considered enabling power save. Also like the idea of changing DIM mode. So I'll combo that.

 

[salsagev]

Here is the 3D printed mount I made that fit Uniden radar detector. Just use the old screw from the mirror.

Updated (latest version not block cabin camera) https://www.printables.com/model/847680-uniden-radar-detector-mount-for-cybertruck
Valentine V1 version made by Dclewis: https://makerworld.com/en/models/483915?from=search

This works like a charm btw. Fits the Uniden R8 perfectly and wiring was extremely simple.

 

[salsagev]

I did the same, but because the camera is always powered, the R8 doesnt turns off when parked and away from the truck. You have that issue?

.

The power to the radar detector if you use the wire above the camera area will stay on until the car goes to sleep after a few minutes. so it doesnt drain a lot of power.

 

[DrShah]

Here is the 3D printed mount I made that fit Uniden radar detector. Just use the old screw from the mirror.

Updated (latest version not block cabin camera) https://www.printables.com/model/847680-uniden-radar-detector-mount-for-cybertruck
Valentine V1 version made by Dclewis: https://makerworld.com/en/models/483915?from=search

Beautiful clean install! I used a Magsafe mount behind the screen and a magnetic ring to mount my R4 directly at eye level.

 

[Nexus6]

That’s a loaded question that starts many of fights on Reddit.

I find the most value on the drive to Vegas from So Cal. On that stretch it has saved me several times. I’ve had it save me a couple times on freeways around LA too. Around town, I can’t say it’s ever saved me. I got hit a few months ago by a motor cycle cop with laser by my house.

My driving style is stay in the fast lane so I only deal with cars coming at me from one side. I go the speed of traffic. If that’s 70 or 80 or 90, fine. If the freeway is wide open, I go 80 or so. It gives me a piece of mind on the freeway. ??‍

Around town, I don’t weave, but I’ll go 55 on a 45. There’s a hill by our house and he got me coming down the hill too fast. 55 in a 40. First ticket in 12 years.

I don’t consider it a cool factor at all. I believe it helps on the freeway and if it helps once, it’s worth it.

My Uniden saved me a number of times. Added an ALP to our Model X and I love the befuddled look of the Cops when they stare at their Laser guns as I pass by. Going to use this mount in the interim while I order the new R-9w Radar/Laser detector with Laser Jamming!

 

[unstatusthequo]

Here is the link.

https://makerworld.com/en/models/483915?from=search

Any reason that wouldn't fit the V2? Seems like the mount angles are very similar.

 

[edsonbarron]

The power to the radar detector if you use the wire above the camera area will stay on until the car goes to sleep after a few minutes. so it doesnt drain a lot of power.

figured you’d be a good person to ask. Any issues after updating to 2025.2.9 or whatever the latest update was?

 

[salsagev]

figured you’d be a good person to ask. Any issues after updating to 2025.2.9 or whatever the latest update was?

Just got back in country and discovered my Radar detector was completely on the entire time since 2025.2.8 update and not powering off when the truck went to sleep like in previous builds. Just updated to 2025.8.4 and will see if it still happens.... was wondering why my tesla was draining when i was gone...

 

[edsonbarron]

Just got back in country and discovered my Radar detector was completely on the entire time since 2025.2.8 update and not powering off when the truck went to sleep like in previous builds. Just updated to 2025.8.4 and will see if it still happens.... was wondering why my tesla was draining when i was gone...

Yeah mine was working in reverse for a week. It would power on while the truck was off. And as soon as I hit the brake to start the truck it would turn off. Did a reset, did the ads service menu reset, reinstalled software like 3 times. Nothing. Left it unplugged for a week and plugged it back in and it started working as normal after that.

 

[Shrey]

Thank you OP + this amazing forum for help with the install. It turned out great and SAVED my ass this week! APPRECIATE you guys so much. Peace & Love!

 

[Nexus6]

I’m using a DLP Resin Printer.
Two attempts have broken as they can’t support the weight.
Anyone have a recommendation on a resin?

Sponsored