You have said something very important and true. The BK leaves the steel more opaque (like a fog). But you say that with alcohol the haze is removed and the original shine is left?
Did you watch and follow the video from out-of-spec-detailing? He said to use Windex after the Bar Keepers Friend. I got myself some of each and was going to try it out today but ran out of time. By the way, did you do it by hand and how long did it take for the whole truck?My Cybertruck was delivered with quite a bit of staining on a lot of the panels. It’s looked to be from rain. I tried a bunch of softer cleaners first to get off the stains. Windex, waterless wash, full soap wash, generic stainless polish, etc.
None of that worked. So I tried some bar keepers friend that many other suggested. I tried it on a small area, and it looked fine. I then tried a door with lots of staining. I let it sit for one minute and then rinsed it off. The first time I applied very lightly and it dulled the stains, but didn’t remove them. The second time I scrubbed just a little more and it completely removed all the stains and created a perfectly uniform panel.
However, The door is now lighter in color and the finish is a bit more dull / less shiny. I don’t love this effect, but it appears I’m going to have to live with it since I already started. I followed the directions, didn’t let it sit too long and didn’t scrub hard. To help others to do this well and decide if this is for them, I would love some advice or feedback from others if they saw this, or if I did something wrong.
Pic: BKF used on rear door only
Important Edit: after finishing the whole truck, I noticed that the front panel in the picture below still doesn’t match the panel in the rear. I am thinking bar keepers friend didn’t change the panel as much as I thought. When both panels were done the same way they still look different. So if my post scared you away, don’t worry too much. The truck looks amazing with all panels done and I do prefer it better now.
There's no reason to use Windex after Bar Keeper's Friend. Just flush with water and wipe dry.
That plastic coating is going to make it more difficult to keep looking nice as it starts to fail. I don't use any coatings on the bare metal and it's super easy to keep looking nice. The bare metal is harder and more scratch resistant than the plastic coating.I had great results with CitriSurf 77 Plus Stainless Steel Rust Remover with clear PPF. Applied HALO ceramic coating to protect the finish and easy cleaning.
Of course it changed the look. You’ve taken a layer off. I did the same thing.My Cybertruck was delivered with quite a bit of staining on a lot of the panels. It’s looked to be from rain. I tried a bunch of softer cleaners first to get off the stains. Windex, waterless wash, full soap wash, generic stainless polish, etc.
None of that worked. So I tried some bar keepers friend that many other suggested. I tried it on a small area, and it looked fine. I then tried a door with lots of staining. I let it sit for one minute and then rinsed it off. The first time I applied very lightly and it dulled the stains, but didn’t remove them. The second time I scrubbed just a little more and it completely removed all the stains and created a perfectly uniform panel.
However, The door is now lighter in color and the finish is a bit more dull / less shiny. I don’t love this effect, but it appears I’m going to have to live with it since I already started. I followed the directions, didn’t let it sit too long and didn’t scrub hard. To help others to do this well and decide if this is for them, I would love some advice or feedback from others if they saw this, or if I did something wrong.
Pic: BKF used on rear door only
Important Edit: after finishing the whole truck, I noticed that the front panel in the picture below still doesn’t match the panel in the rear. I am thinking bar keepers friend didn’t change the panel as much as I thought. When both panels were done the same way they still look different. So if my post scared you away, don’t worry too much. The truck looks amazing with all panels done and I do prefer it better now.
BKF is an abrasive and will f up your truck. You should use a petroleum based product like WD40.My Cybertruck was delivered with quite a bit of staining on a lot of the panels. It’s looked to be from rain. I tried a bunch of softer cleaners first to get off the stains. Windex, waterless wash, full soap wash, generic stainless polish, etc.
None of that worked. So I tried some bar keepers friend that many other suggested. I tried it on a small area, and it looked fine. I then tried a door with lots of staining. I let it sit for one minute and then rinsed it off. The first time I applied very lightly and it dulled the stains, but didn’t remove them. The second time I scrubbed just a little more and it completely removed all the stains and created a perfectly uniform panel.
However, The door is now lighter in color and the finish is a bit more dull / less shiny. I don’t love this effect, but it appears I’m going to have to live with it since I already started. I followed the directions, didn’t let it sit too long and didn’t scrub hard. To help others to do this well and decide if this is for them, I would love some advice or feedback from others if they saw this, or if I did something wrong.
Pic: BKF used on rear door only
Important Edit: after finishing the whole truck, I noticed that the front panel in the picture below still doesn’t match the panel in the rear. I am thinking bar keepers friend didn’t change the panel as much as I thought. When both panels were done the same way they still look different. So if my post scared you away, don’t worry too much. The truck looks amazing with all panels done and I do prefer it better now.
Absolutely not true. You can get the Oxalic/citrus acid only version that is 100% non abrasive.BKF is an abrasive and will f up your truck. You should use a petroleum based product like WD40.
True, and the non-abrasive version is the only one I would recommend. And I wouldn't follow Out of Spec Detailing's advice and follow it up with Windex, they have more trouble, more time and expense, maintaining their Cybertruck than anyone. And it requires frequent re-dos.
That also is not true.
